Showing results: 316 - 330 of 2454 items found.
-
-
Premier Electrosystems
The typical use of high voltage testing is to confirm performance. The high voltage tests are included in type and routine tests to meet the required IS standards, quality and reliability. Some of them are insulation resistance tests, dielectric type tests, lightning and switching impulse tests, partial discharge measurement, etc. Premier's high voltage tester checks the insulation between line to earth, neutral to earth, primary to earth, secondary to earth and between primary & secondary.
-
1669 -
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems, test for circuit and spark plug.1. Check spark plug on secondary or high voltage. 2. Use as a continuity tester to check on low voltage circuits.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Pickering Interfaces Ltd.
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
Series 67 & 68 -
Pickering Electronics
Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.
-
SGMF(T) Series -
Shanghai Jiuzhi Electric Co., Ltd.
Onsite mobile AC high voltage test systems are used for withstand voltage testing, partial discharge measurement, tan delta measurement to instrument transformers, GIS, GIL, switchgears and etc after they are installed onsite and for purposes of diagnostics in asset management up to 900kV/10A.
-
KM 6213AIN -
Kusam Electrical Industries Limited
• The KM 6213A IN is the KUSAM-MECO premium model of High Voltage Digital Insulation Resistance Testers.• The KM 6213A IN has new added features with a low consumption High Performance processor.• It displays results much faster and has more advanced features.• The KM 6213A IN has Automatic Polarization Index and Dielectric Absorption Ratio Calculations.• Results are displayed on the new High Contrast LCD. It’s mounting angle makes it more readable for all users, in different working conditions.• The user’s manual reflects the new features and added benefits of this instrument.• It has Auto-Off, Auto-Stop, EnerSave™ and is a non destructive tester.• Once you start the tester, it waits for your selection. You can go up and down in voltage to select the voltage at which you want to test the insulation. Once you have selected that voltage, you need to connect the test leads to the Insulation Tester to measure. Then it measures voltage to ensure there is no voltage present on the equipment under test. If there is a voltage present, it will warn you to disconnect the circuit before proceeding. If it’s free of any voltage, then you can proceed with the testing. This ensures that no damage is done to the Insulation Tester KM 6213AIN.• One of the new innovation on this tester is also the way the new unique calibration process works. It’s fully digital, has no moving parts and does not require expensive and complicated jigs or computers systems to be calibrated. It’s cheaper to maintain than any other Digital HV Insulation tester on the market today. The KM 6213AIN is supplied standard with our Premium test Leads Kit, the AL-50.
-
CMTI-8010A -
High Power Pulse Instruments GmbH
The CMTI-8010A is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
CMTI-8010C -
High Power Pulse Instruments GmbH
The CMTI-8010C is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
RK7112 -
Shenzhen Chuangxin Instruments Co., Ltd.
The tester is applied to the home appliances, computer peripheral equipment, electric products, communication products, lighting products, small home appliance products, lighting equipment, electronic components, transformers, motors, compressors, electric heat pipe, wire, cable and high voltage safety system’s withstand voltage and leakage current test, as well as it’s an indispensable dielectric
-
PPE6KV-A -
Teledyne LeCroy
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
TD2000A -
Ponovo Power Co., Ltd.
TD series testing equipment is a High Voltage DC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.